Terms and Conditions
Terms for using this website and the principles that govern our services. Last updated 21 November 2026.
About these terms
This website is operated by Al-Meezan Industrial Metrology Services (AIMS), House # 58, B Block, OPF Housing Society, Lahore, Pakistan. By using the website or requesting our services you agree to these terms. Individual jobs are also governed by the quotation or agreement issued for that work; where the two differ, the quotation or agreement takes priority.
Use of the website
The content on this site describes our general capabilities and is provided for information. It is not a binding offer. Please do not misuse the website, attempt to disrupt it, or submit false or unlawful information through its forms.
Quotations and orders
- A request submitted through the website is an enquiry. A contract is formed only when AIMS confirms a quotation in writing and the customer accepts it.
- Prices, turnaround, service location, and the scope of work are those stated in the quotation.
- If we find that the requested work cannot be carried out as agreed, we will inform the customer before proceeding.
Calibration, testing, and inspection services
- Results relate only to the items calibrated, tested, or inspected, in the condition they were received and at the time the work was done.
- Accredited status applies only to work within our PNAC scope of accreditation and is stated on the certificate. The current certificate and scope are published on the Credentials page.
- Certificates and reports may not be reproduced except in full without written approval from AIMS.
- The customer decides calibration intervals and whether an instrument is fit for its intended use, unless a statement of conformity has been agreed in the quotation.
Impartiality and integrity
Our work is carried out under the AIMS management policy on confidentiality, impartiality, integrity, and freedom from undue pressure. Under that policy, AIMS management is committed to:
- Making sure laboratory employees understand the quality management system and its procedures, and apply them in practice.
- Providing a working environment in which personnel are free from undue commercial, financial, or other pressures that might influence their technical judgement.
- Ensuring employees do not use their position for private gain, act impartially, and give no preferential treatment to any organization or individual.
- Protecting customer confidential information, including through a confidentiality agreement signed by every employee.
- Taking care that AIMS and its employees do not engage in any activity that could endanger trust in the independence of judgement and integrity of our testing and calibration work.
In keeping with this policy, results are reported as measured. Customers must not offer gifts, payments, or other inducements to AIMS personnel, or put pressure on them to change a result, a certificate date, or a statement of conformity. AIMS may decline or stop work where its impartiality would be compromised.
Confidentiality
Information obtained or created while performing work for a customer is treated as confidential and is released only to the customer or to a person the customer has authorized, unless disclosure is required by law or by our accreditation body. Details are set out in our Privacy Policy.
Customer responsibilities
- Provide accurate details of the instruments, ranges, and requirements for the work.
- Send instruments clean, safe to handle, and with any accessories, manuals, or software needed to operate them.
- For on-site work, provide safe access, suitable environmental conditions, and the utilities needed to carry out the calibration.
- Tell us about any known faults or hazards before work begins.
Complaints
If you are not satisfied with our work or with the conduct of our personnel, contact us using the details below. Complaints are recorded, investigated, and answered under our quality management system.
Intellectual property
The text, graphics, logos, and documents on this website belong to AIMS or are used with permission. The PNAC accreditation documents are published for verification and may not be altered or used to imply accreditation of any other organization.
Limitation of liability
We take care to keep the information on this website accurate, but it is provided without warranty and may change without notice. To the extent permitted by law, AIMS is not liable for any indirect or consequential loss arising from use of the website or reliance on its content. Liability for services is as set out in the quotation or agreement for that work.
Governing law
These terms are governed by the laws of Pakistan. Any dispute relating to them is subject to the jurisdiction of the courts at Lahore.
Changes and contact
We may update these terms from time to time; the current version is always published on this page. Questions: info@aimscal.com or +92 301 0002467.
